Lenco Marine

Lenco 1.25 XDS 5 Lobe Actuator - 12V - 1-1/4" Stroke

$250.99 $300.00

1.25 XDS 5 Lobe Actuator - 12V - 1-1/4" Stroke

• Model: 1.25 XDS
  
• Stroke: 1.25"
  
• Hole: 5/16"

View full product details

Lenco 101 Standard Actuator - 24V - 2-1/4" Stroke

$236.99 $287.00

101 Standard Actuator

5/16" (.79 cm) mounting hardware
Stroke: 2-1/4" (5.72 cm)
Length overall: 12-1/8" (30.80 cm)
Length pin to pin: 11-1/2" (29.21 cm)
Diameter (upper housing): 2-1/2" (6.35 cm)
Mounting hardware: 5/16" ( .79 cm) or Delrin Pin (Part #121)

Part # (Superseded #)
15061-001(101-3), 24 Volt w/6' (1.83 cm) cable with Deutsch connector & mounting hardware(replacement length)

• Top cap gland seal sheaths the actuator cable outer jacket as well as both internal conductors for maximum waterproofing
  
• Corrosion proof Vandar mounts
  
• Stainless steel ram won't flex, even under extreme loads
  
• Double O-ring for maximum protection
  
• Ballscrew rotates freely on 12 ball bearings at both ends of its stroke so there's no need for complicated limit switches and clutches
  
• Self-locking ballscrew locks into position and will not drift
  
• Precision molded, powdered metal, high alloy gears provide high accuracy, high wear resistance, and high strength for long life
  
• Tough, high-torque motor easily transfers 750 lbs
  
• High-impact, ultraviolet resistant nylon 66, 50% glass fiber reinforced thermoplastic housing
  
• Corrosion proof Vandar cap and mount, stands up to severe loads

View full product details

Lenco 101XD Extreme Duty Actuator - 12V - 2 1/4" Stroke - 3/8" Hardware

$237.99 $288.00

101 XD Extreme Duty Actuator

Part # (Superseded #)
#15056-001 (101 XD-7) 12 Volt w/6' (1.83 m) leads with Deutsch connectors, and 3/8" (.95 cm) mounting hardware. Solid stainless steel billet end
Included in Extreme Duty Performance Kits, High Performance Trim Tab Kits and Super Strong Kits
Stroke: 2-1/4" (5.72 cm)
Length overall: 11-3/8" (28.89 cm)
Length pin to pin: 10-3/4" (27.31)
Diameter (upper housing): 2-1/2" (6.35 cm)

• Top cap gland seal sheaths the actuator cable outer jacket as well as both internal conductors for maximum waterproofing
  
• Corrosion proof Vandar mounts
  
• Stainless steel ram won't flex, even under extreme loads
  
• Double O-ring for maximum protection
  
• Ballscrew rotates freely on 12 ball bearings at both ends of its stroke so there's no need for complicated limit switches and clutches
  
• Self-locking ballscrew locks into position and will not drift
  
• Precision molded, powdered metal, high alloy gears provide high accuracy, high wear resistance, and high strength for long life
  
• Tough, high-torque motor easily transfers 750 lbs
  
• High-impact, ultraviolet resistant nylon 66, 50% glass fiber reinforced thermoplastic housing
  
• Corrosion proof Vandar cap and mount, stands up to severe loads

View full product details

Lenco 101XD Extreme Duty Actuator - 12V - 2-1/4" Stroke - 5/16" Hardware

$237.99 $288.00

101 XD Extreme Duty Actuator

Part # (Superseded #)
#15055-001 (101 XD-5) 12 Volt w/6' (1.83 m) leads with Deutsch connectors
and 5/16" (.79 cm) mounting hardware. Solid stainless steel billet end,
Included in Heavy Duty PerformanceTab Kits
Stroke: 2-1/4" (5.72 cm)
Length overall: 11-3/8" (28.89 cm)
Length pin to pin: 10-3/4" (27.31)
Diameter (upper housing): 2-1/2" (6.35 cm)

• Top cap gland seal sheaths the actuator cable outer jacket as well as both internal conductors for maximum waterproofing
  
• Corrosion proof Vandar mounts
  
• Stainless steel ram won't flex, even under extreme loads
  
• Double O-ring for maximum protection
  
• Ballscrew rotates freely on 12 ball bearings at both ends of its stroke so there's no need for complicated limit switches and clutches
  
• Self-locking ballscrew locks into position and will not drift
  
• Precision molded, powdered metal, high alloy gears provide high accuracy, high wear resistance, and high strength for long life
  
• Tough, high-torque motor easily transfers 750 lbs
  
• High-impact, ultraviolet resistant nylon 66, 50% glass fiber reinforced thermoplastic housing
  
• Corrosion proof Vandar cap and mount, stands up to severe loads

View full product details

Lenco 12" x 30" Super Strong Trim Tab Kit w/o Switch Kit 12V

$1,045.99 $1,415.00

Super Strong Trim Tabs

Designed for sport-fishing boats, high speed cruising boats and large commercial vessels. 7 Gauge flat - 304 SS blades with all stainless steel mounting hardware withstand the rigors of the most demanding conditions. No spray or mist when mounted in recessed pockets. 3/8" diameter hinge pin and 3.75" sacrificial anode. Single Actuator Systems have Vandar Upper Mounting Brackets with Gland Seal (#15085-001) and 10 Ga. SS lower mounting brackets with 3/8" SS bolts. Dual Actuator Systems have 10 Ga SS upper and lower mounting brackets with 3/8" SS bolts.

We make the best boats better!™

Yes, we build serious trim tabs for serious vessels. We know there are boats and conditions that require a little more performance. This is why we created the Super Strong series. Whether your're running a pleasure cruiser in search of your own personal paradise or spending your days backing down on marlin in some new hot spot you've just discovered, we've got our covered. We've utilized a 7-gauge stainless steel blade and all extreme-duty mounting hardware to create a trim tab system that can withstand the rigors of the most demanding conditions.

• Instant response, extreme-duty electric actuators for precise control
  
• 7-gauge laser cut stainless steel blades mean no bending or flexing
  
• Heavy duty stainless steel mounting hardware
  
• Welded stainless steel billet ram ends for extra strength
  
• Dual ram available for the most extreme-duty applications
  
• No spray or mist when mounted in recessed pockets
  
• Stitch welded heavy duty stainless steel hinge with 3/8" hinge rod

• High-impact, 50% glass fiber-filled, ultraviolet resistant nylon case
  
• Extreme-duty electric actuators are fully submersible, maintenance-free and sealed for life
  
• Electro-polished solid 316 stainless steel billet end for extreme-duty
  
  Each Kit Includes:
  
  • 2 SS Trim Tab Planes
    
  • 2 Actuators with 6' Lead and Deutsch Plugs
    
  • All Necessary Steel Mounting Hardware
    
  • Actuator Extension Harnesses (2 for Single Actuator Application) will be required
  .

  Specifications:

  • Box Dimensions: 5"H x 13"W x 32"L WT: 57 lbs
  • UPC: 874847004428
  
  Brochure (pdf)

View full product details

Lenco 12" x 9" Electro-Polished Edge Mount Trim Tab Kit

$547.99 $730.00

12" x 9" Electro-Polished Edge Mount Trim Tab Kit
12 Volt

Fast response electric actuators for precise control. Fully submersible. All Plug & Play Deutsch connections. Electro-Polished blades are constructed of 12-gauge 304 stainless steel with 1" turned up edges and an 85x inside taper and 1/8" diameter stainless steel hinge pin. The actuators mount at the trailing edge of the blades, requiring 1/2" less transom height than the standard mount tabs.

Kits include:

• (2) 12-gauge stainless steel Electro-Polished blades
  
• (2) 15054-001 actuator with 6' leads and Deutsch connectors
  
• (2) 30133-103 20' actuator extension wiring harnesses
  
• (2) 15085-001 upper mounting brackets with gland seal
  
• (2) 50014-001 lower mounting brackets
  
• Lenco owner's/installation manual
  
• Stainless steel mounting hardware

• Boat Length:14' - 18'
  
• L" x W":12" x 9"
  
• Hinge Height:2"
  
• Minimun Transom Height:11"

Specifications:

• Construction: Stainless Steel
• Boat Length - Max (Feet): 14'-18'
• Actuator Type: Electro-Mechanical
• Box Dimensions: 5"H x 13"W x 14"L WT: 17 lbs
• UPC: 874847006798

View full product details

Lenco 18" x 14" Standard Performance Trim Tab Kit w/o Switch Kit 12V

$771.99 $1,045.00

Standard Performance Series Tabs


Standard actuator with 5/16" stainless steel through bolts. 1" turned up edges with 2" taper on the inside. All 12-gauge 304 stainless steel construction with Electro-Polished Blades

We make the best boats better!™

Running wide open in rough seas isn't for the faint of heart. Aggressive boating requires durable boat accessories. Lenco's Standard Performance series of trim tabs are built to handle whatever you or Mother Nature might throw at them. Everything about your boat is designed to go hard and fast. Why should your trim tab system be any different?

• All stainless steel construction (no dissimilar metals), Electro Polished Blades for long lasting good looks
  
• Actuator speed is precise and controllable so there are no surprises at top speeds

• Instant response
  
• Fully submersible, maintenance-free and sealed for life
  
• High-impact, 50% glass fiber-filled, ultrabiolet-resistant nylon case

• 2 actuators with 6' Lead & Deutsch Plugs
  
• 2 12 Gauge SS Electro Polished trim tab planes
  
• 2 20' Actuator Extension Wiring Harness
  
• 2 Upper Mounting Bracket with Gland Seal
  
• 2 Lower Mounting Bracket
  
• All Necessary stainless steel mounting Hardware

View full product details

Lenco 2 Delrin Mounting Pins f/101 & 102 Actuator (Pack of 2)

$8.99 $10.50

Delrin Mounting Pin for 101 & 102 Actuator (1.5") - Pack of 2.

View full product details

Lenco 4" x 12" Limited Space Trim Tab Kit w/o Switch Kit 12V - Electro-Polished - Standard Actuator

$464.99 $605.00

Limited Space Trim Tab Kits

12-Gauge Blades / 12-Volt Actuators

Lenco Electric Limited Space Trim Tab Kits are ideal for boats with a swim platform and/or ladder. They can be fitted to transoms that have a limited mounting area. Blades are 12 gauge - 304 SS with front of blade folded to provide a smooth trailing edge and 1/8" diameter hinge pin. Fast response electric actuators for precise control. All units have Plug and Play connections and are fully submersible.

Kit Contents

• 2 each of 12-gauge 304 stainless steel trim tab blades
  
• 2 each of #15054-001 Standard actuator with 6' lead and Deutsch plugs
  
• 2 each of #30133-103 20' actuator extension wiring harnesses
  
• 2 each of #15085-001 (116) upper mounting bracket with gland seal
  
• 1 each of the Lenco owner's / installation manual
  
• All necessary stainless steel mounting hardware

• Trim Tab Kit: Limited Space
  
• Blades: 12 Gauge Stainless Steel
  
• Finish: Electro-Polish
  
• Switch Kit: Sold Separately
  
• Class: Fuel Efficient
  
• Compliance: CE Certified
  
• Compatibility: Any Boat
  
• Made in: Stuart, Florida U.S.A.

Specifications:

• Actuator Type: Electro-Mechanical
• Construction: Stainless Steel
• Box Dimensions: 5"H x 13"W x 14"L WT: 14 lbs
• UPC: 874847007115

View full product details

Lenco 7 Degree Mounting Shim f/118 & 119 Mounting Brackets

$10.99 $12.85

7 Degree Mounting Shim For Upper # 50015-001D(118) & Lower # 50014-001D(119) Mounting Bracket.

View full product details

Lenco Actuator Extension Harness - 45' - 10 Awg

$100.99 $120.00

Actuator Extension Harness - 45' - 10 Awg

• 45' Deutsch-Connected Extension
  
• 10 Awg
  
• Abyc Compliant

View full product details

Lenco Auto Glide Adapter Extension Cable - 5'

$58.99 $62.00

Extension Cable - 5'

Extension Cable for Engine Adapter Cable, CAN #1 & CAN #2

For use with:
30246-001
30252-001
30277-001
30259-001
30257-001

View full product details

Lenco Bennett Retrofit Kit - 24V

$345.99 $420.00

Bennett RetroFit Kit

We make the best boats better!™

Lenco Marine Electric RetroFit Kit for Bennett Trim Tabs

Upgrade your boat with the latest trim tab technology - trouble-free, high performance Lenco electric actuators.

Easy installation:

• Use existing Bennett trim planes, lower bracket and switch
  
• Use all existing mounting holes

• 2 electric actuators
  
• 2 upper mounting brackets
  
• Switch wiring kit
  
• All mounting hardware

• Lenco wire feeds through existing oil line hole in transom
  
• Lenco upper mounting bracket fits existing Bennett mounting holes
  
• Existing Bennett trim tab plane and hinge
  
• Existing Bennett lower bracket

• Remove Bennett actuators, and install Lenco upper mounting brackets on transom
  
• Feed Lenco wires through holes in brackets and through existing oil line holes in transom
  
• Mount Lenco actuators on to new upper brackets and existing Bennett lower brackets
  
• Connect Lenco actuator wires to existing harness.

View full product details

Lenco Compact Upper Mounting Bracket - 2 Screws 1 Wire

$11.99 $14.25

Compact Upper Bracket - VANDAR - (2 screw, 1 wire) (Used in applications with limited space)

View full product details

Lenco Standard Integrated Tactile Switch Kit w/Pigtail f/Dual Actuator Systems

$162.99 $208.00

Standard Integrated Tactile Switch Kit w/Pigtail f/Dual Actuator Systems

This switch has the control box integrated into the back of the switch Key Pad. There is no external control box for this kit. Wiring harness is 30"(76.2 cm)in length from the end of the switch bezel.

This technology improves accuracy and integrates the control box functionality into the key pad bezel.

View full product details

Lenco Tactile Trim Tab Switch Kit - Standard

$159.99 $208.00

Standard Solid State Tactile Switch Kits with Retractor Feature
#15069-001 (124SSR)
For 12-volt single actuator systems. Control box is waterproof, self-contained, sealed, solid state, Deutsch connected for easy Plug & Play installation, and features built-in retractor. Kit includes 36" power pigtail and nylon nuts for mounting keypad. Colorful display box.

Features

• Built-In Retractor Feature
  
• Solid State Electronics
  
• Plu & Play
  
• Low Profile Design
  
• Self-Contained, sealed keypad & solid state control box with waterproof connectors
  
• Simple, Quick Installation
  
• Includes 36" power pigtail for control box
  
• 2" hole cut-out size, overall size 2.75" x 2.75'

View full product details

Lenco 101 Standard Actuator - 12V - 2-1/4" Stroke

$192.99 $234.00

101 Standard Actuator

Included in Standard Trim Tab Kit, Standard Performance Tab Kit and Bennett Retrofit Kit

5/16" (.79 cm) mounting hardware
Stroke: 2-1/4" (5.72 cm)
Length overall: 12-1/8" (30.80 cm)
Length pin to pin: 11-1/2" (29.21 cm)
Diameter (upper housing): 2-1/2" (6.35 cm)
Mounting hardware: 5/16" ( .79 cm) or Delrin Pin (Part #121)

Part # (Superseded #)
#15054-001 (101-2), 12 Volt w/6' (1.83 cm) cable with Deutsch connector & mounting hardware (replacement length)

• Top cap gland seal sheaths the actuator cable outer jacket as well as both internal conductors for maximum waterproofing
  
• Corrosion proof Vandar mounts
  
• Stainless steel ram won't flex, even under extreme loads
  
• Double O-ring for maximum protection
  
• Ballscrew rotates freely on 12 ball bearings at both ends of its stroke so there's no need for complicated limit switches and clutches
  
• Self-locking ballscrew locks into position and will not drift
  
• Precision molded, powdered metal, high alloy gears provide high accuracy, high wear resistance, and high strength for long life
  
• Tough, high-torque motor easily transfers 750 lbs
  
• High-impact, ultraviolet resistant nylon 66, 50% glass fiber reinforced thermoplastic housing
  
• Corrosion proof Vandar cap and mount, stands up to severe loads

View full product details

Lenco 102 Series Standard Actuator - 12V - 4-1/4" Stroke

$237.99 $288.00

102 Actuator

Used with Troll'n Tab Kits prior to 2000
5/16" (.79 cm) mounting hardware
Stroke: 4-1/4" (10.8 cm)
Length overall: 14" (35.56 cm)
Length pin to pin: 13" (32.87 cm)
Diameter (upper housing): 2-1/2" (6.35 cm)
Mounting hardware: 5/16" (.79 cm) or Delrin Pin (Part #15087-001)

Part # (Superceded #)
# 15059-001 (102-2) 12 Volt w/6' (1.83m) leads with Deutsch connectors and mounting hardware(replacement length)

• Top cap gland seal sheaths the actuator cable outer jacket as well as both internal conductors for maximum waterproofing
  
• Corrosion proof Vandar mounts
  
• Stainless steel ram won't flex, even under extreme loads
  
• Double O-ring for maximum protection
  
• Ballscrew rotates freely on 12 ball bearings at both ends of its stroke so there's no need for complicated limit switches and clutches
  
• Self-locking ballscrew locks into position and will not drift
  
• Precision molded, powdered metal, high alloy gears provide high accuracy, high wear resistance, and high strength for long life
  
• Tough, high-torque motor easily transfers 750 lbs
  
• High-impact, ultraviolet resistant nylon 66, 50% glass fiber reinforced thermoplastic housing
  
• Corrosion proof Vandar cap and mount, stands up to severe loads

View full product details

Lenco 102XD Extreme Duty Actuator - 12V - 4-1/4" Stroke

$263.99 $320.00

102 XD Actuator

Used with Troll n Tab Kits 2000 to present & various OEM Applications
5/16" (.79 cm) mounting hardware
Stroke: 4-1/4" (10.8 cm)
Length overall: 12-7/8" (32.70 cm)
Length pin to pin: 12-1/4" (31.11 cm)
Diameter (upper housing): 2-1/2" (6.35 cm)
Mounting hardware: 5/16" (.79 cm) or Delrin Pin (Part #15087-001)

Part #
#15060-001 (102-2) 12 Volt w/6' (1.83m) leads with Deutsch connectors and mounting hardware(replacement length)

• Top cap gland seal sheaths the actuator cable outer jacket as well as both internal conductors for maximum waterproofing
  
• Corrosion proof Vandar mounts
  
• Stainless steel ram won't flex, even under extreme loads
  
• Double O-ring for maximum protection
  
• Ballscrew rotates freely on 12 ball bearings at both ends of its stroke so there's no need for complicated limit switches and clutches
  
• Self-locking ballscrew locks into position and will not drift
  
• Precision molded, powdered metal, high alloy gears provide high accuracy, high wear resistance, and high strength for long life
  
• Tough, high-torque motor easily transfers 750 lbs
  
• High-impact, ultraviolet resistant nylon 66, 50% glass fiber reinforced thermoplastic housing
  
• Corrosion proof Vandar cap and mount, stands up to severe loads

View full product details

Lenco Bennett Retrofit Kit - 12V

$325.99 $395.00

Bennett RetroFit Kit

We make the best boats better!™

Lenco Marine Electric RetroFit Kit for Bennett Trim Tabs

Upgrade your boat with the latest trim tab technology - trouble-free, high performance Lenco electric actuators.

Easy installation:

• Use existing Bennett trim planes, lower bracket and switch
  
• Use all existing mounting holes

• 2 electric actuators
  
• 2 upper mounting brackets
  
• Switch wiring kit
  
• All mounting hardware

• Lenco wire feeds through existing oil line hole in transom
  
• Lenco upper mounting bracket fits existing Bennett mounting holes
  
• Existing Bennett trim tab plane and hinge
  
• Existing Bennett lower bracket

• Remove Bennett actuators, and install Lenco upper mounting brackets on transom
  
• Feed Lenco wires through holes in brackets and through existing oil line holes in transom
  
• Mount Lenco actuators on to new upper brackets and existing Bennett lower brackets
  
• Connect Lenco actuator wires to existing harness.

View full product details

Lenco 12" x 9" Standard Performance Trim Tab Kit w/Standard Tactile Switch Kit 12V

$713.99 $966.00

Standard Performance Series Tabs


Standard actuator with 5/16" stainless steel through bolts. 1" turned up edges with 2" taper on the inside. All 12-gauge 304 stainless steel construction with Electro-Polished Blades

We make the best boats better!™

Running wide open in rough seas isn't for the faint of heart. Aggressive boating requires durable boat accessories. Lenco's Standard Performance series of trim tabs are built to handle whatever you or Mother Nature might throw at them. Everything about your boat is designed to go hard and fast. Why should your trim tab system be any different?

• All stainless steel construction (no dissimilar metals), Electro Polished Blades for long lasting good looks
  
• Actuator speed is precise and controllable so there are no surprises at top speeds

• Instant response
  
• Fully submersible, maintenance-free and sealed for life
  
• High-impact, 50% glass fiber-filled, ultraviolet-resistant nylon case

• Built-In Retractor Feature
  
• Solid State Electronics
  
• Plug & Play
  
• Low Profile Design
  
• Self-Contained, sealed keypad & solid state control box with waterproof connectors
  
• Simple, Quick Installation
  
• Includes 36" power pigtail for control box
  
• 2" hole cut-out size, overall size 2.75" x 2.75'

• Standard Tactile Switch Kit
  
  2 actuators with 6' Lead & Deutsch Plugs
  
  • 2 12 Gauge SS Electro Polished trim tab planes
    
  • 2 20' Actuator Extension Wiring Harness
    
  • 2 Upper Mounting Bracket with Gland Seal
    
  • 2 Lower Mounting Bracket
    
  • All Necessary stainless steel mounting Hardware

  Specifications:

  • Box Dimensions: 5"H x 14"W x 15"L WT: 20.18 lbs
  
  Brochure (pdf)

View full product details

Lenco 12" x 9" Standard Performance Trim Tab Kit w/o Switch Kit 12V

$559.99 $758.00

Standard Performance Series Tabs


Standard actuator with 5/16" stainless steel through bolts. 1" turned up edges with 2" taper on the inside. All 12-gauge 304 stainless steel construction with Electro-Polished Blades

We make the best boats better!™

Running wide open in rough seas isn't for the faint of heart. Aggressive boating requires durable boat accessories. Lenco's Standard Performance series of trim tabs are built to handle whatever you or Mother Nature might throw at them. Everything about your boat is designed to go hard and fast. Why should your trim tab system be any different?

• All stainless steel construction (no dissimilar metals), Electro Polished Blades for long lasting good looks
  
• Actuator speed is precise and controllable so there are no surprises at top speeds

• Instant response
  
• Fully submersible, maintenance-free and sealed for life
  
• High-impact, 50% glass fiber-filled, ultrabiolet-resistant nylon case

• 2 actuators with 6' Lead & Deutsch Plugs
  
• 2 12 Gauge SS Electro Polished trim tab planes
  
• 2 20' Actuator Extension Wiring Harness
  
• 2 Upper Mounting Bracket with Gland Seal
  
• 2 Lower Mounting Bracket
  
• All Necessary stainless steel mounting Hardware

Specifications:

• Box Dimensions: 5"H x 14"W x 15"L WT: 19.18 lbs
• UPC: 874847000758

View full product details

Lenco 101XDS Short Extreme Duty Actuator - 12V - 2-1/4" Stroke w/5/16" Hardware

$240.99 $288.00

101XDS Short Extreme Duty Actuator - 12V - 2-1/4" Stroke w/5/16" Hardware

• Wire Length:6'
  
• Top Cap Hole:5/16"
  
• End Hole:5/16"

• Stronger top cap and mounting clevis design
  
• Improved pressure-tight torx screws
  
• Integrated wiper seal at actuator base
  
• Molded-in brass thrust bearing design
  
• Thicker and stronger motor housing wall
  
• Improved O-Ring design for more consistant seal
  
• Over-molded cable providing a stronger tighter seal
  
• Upper mounting bracket with gland seal

View full product details

Lenco 18" x 14" Standard Performance Trim Tab Kit w/Standard Tactile Switch Kit 12V

$925.99 $1,253.00

Standard Performance Series Tabs


Standard actuator with 5/16" stainless steel through bolts. 1" turned up edges with 2" taper on the inside. All 12-gauge 304 stainless steel construction with Electro-Polished Blades

We make the best boats better!™

Running wide open in rough seas isn't for the faint of heart. Aggressive boating requires durable boat accessories. Lenco's Standard Performance series of trim tabs are built to handle whatever you or Mother Nature might throw at them. Everything about your boat is designed to go hard and fast. DWhy should your trim tab system be any different?

• All stainless steel construction (no dissimilar metals), Electro Polished Blades for long lasting good looks
  
• Actuator speed is precise and controllable so there are no surprises at top speeds

• Instant response
  
• Fully submersible, maintenance-free and sealed for life
  
• High-impact, 50% glass fiber-filled, ultraviolet-resistant nylon case

• Built-In Retractor Feature
  
• Solid State Electronics
  
• Plug & Play
  
• Low Profile Design
  
• Self-Contained, sealed keypad & solid state control box with waterproof connectors
  
• Simple, Quick Installation
  
• Includes 36" power pigtail for control box
  
• 2" hole cut-out size, overall size 2.75" x 2.75'

• Standard Tactile Switch Kit
  
  2 actuators with 6' Lead & Deutsch Plugs
  
  • 2 12 Gauge SS Electro Polished trim tab planes
    
  • 2 20' Actuator Extension Wiring Harness
    
  • 2 Upper Mounting Bracket with Gland Seal
    
  • 2 Lower Mounting Bracket
    
  • All Necessary stainless steel mounting Hardware

  Specifications:

  • Box Dimensions: 9"H x 19"W x 24"L WT: 32 lbs
  
  Brochure (pdf)

View full product details

Lenco Stainless Steel Mounting Pin f/Hatch Lifts

$11.99 $14.00

Replacemnet Stainless Steel Pull Pin for Hatchlifts (1)

View full product details

Lenco Actuator Extension Harness - 32' - 12 Awg

$66.99 $79.00

Actuator Extension Harness - 32' - 12 Awg

• 32' Deutsch-Connected Extension
  
• 12 Awg
  
• Abyc Compliant

View full product details

Lenco 12" x 12" Edge Mount Trim Tab Kit w/Double Rocker Switch Kit

$611.99 $816.00

12" x 12" Edge Mount Trim Tab Kit w/Double Rocker Switch Kit
12-Gauge Blades / 12V Actuators

Lenco Electric Edge Mount Trim Tab Kits make your boat ride smoother, dryer, faster and with increased safety whether on a small skiff or a large yacht. The Lenco ball screw design is more reliable, three times more powerful and features an instant response, which makes them very user friendly compared to typical hydraulics. Lenco fast response electric actuators are fully submersible with all plug & play waterproof Deutsch connections. Edge Mount actuators mount at the trailing edge of the plane, requiring 4" (10.16 cm) less transom height than Lenco standard mount trim tabs.

Suggested Boat Length: 17'-30'
L" x W": 12" x 12"
Hinge Height: 2"
Minimum Transom Height: 11"

Kit Contents

• 2 each of 12-gauge stainless steel trim tab blades
  
• 2 each of #15054-001 actuator with 6' leads and Deutsch plugs
  
• 2 each of #30133-103 20' actuator extension wiring harnesses
  
• 2 each of #15085-001 (116) upper mounting brackets with gland seal
  
• 2 each of #50014-001 (119) lower mounting brackets
  
• 1 each of the Lenco owner's / installation manual
  
• All necessary stainless steel mounting hardware

• Blades: 12 Gauge Stainless Steel
  
• Finish: Smooth
  
• Class: Fuel Efficient
  
• Compliance: CE Certified
  
• Compatibility: Any Boat

• #122 Carling Double Rocker Switch
  
• Deutsch Conntectors
  
• 36" Power Pigtail
  
• Installation hardware included

Specifications:

• Construction: Stainless Steel
• Boat Length - Max (Feet): 17'-30'
• Box Dimensions: 6"H x 14"W x 13"L WT: 20.2 lbs
• UPC: 874847006187

View full product details

Lenco Upper Mounting Bracket w/Gland Seal (2008-Present)

$11.99 $13.50

Upper Mounting Bracket w/Gland Seal - VANDAR - (3 screw, 1 wire) (2008-Present)

View full product details

Lenco Standard Upper Mounting Bracket - 3 Screws 1 Wire

$10.99 $12.85

Standard Upper Mounting Bracket - VANDAR - (3 screw, 1 wire) (THRU 2007)

View full product details

Lenco Carling Double Rocker Switch Kit

$86.99 $104.00

Double Rocker Trim Tab Switch #122

Features:

• Waterproof Plug & Play Deutsch connections
  
• Hole cut out: 2-1/4"
  
• Overall size: 2-3/4" x 2-3/4"
  
• 12 Volt

View full product details

Lenco Auto Glide Boat Leveling System f/Dual Actuator Tab Systems w/Existing NMEA 2000

$1,348.99 $1,475.00

Lenco Auto Glide Boat Leveling System f/Dual Actuator Tab Systems w/Existing NMEA 2000

A Real Automatic Boat Control / Trim Tab Control System that actually works - completely & automatically!

The Auto Glide system controls your trim tabs from the time you leave your dock until you come home again!

The Auto Glide uses engine data and GPS data (depending on your installation method) to drive your boat to the most efficient running angle by adjusting your Lenco trim tabs as needed. This optimum running angle is determined during the set-up process after the installation of your Auto Glide system.

Imagine that your boat's running angle is measured 25 times per second and this data is used by the new Auto Glide control box to:

• Automatically put your boat in the most efficient running angle.
  
• Reduce the amount of bow rise of your boat during hole shot mode.
  
• Eliminate bow porpoising (bow bounce).
  
• Keep your boat level at all times.

• The Lenco Glide System will work on ALL boats with ALL engines. GPS data is used to provide data to control box. Optional connection to NMEA 2000 Network is included.For OEM System:

• Connection to analog systems is available.
  
• Connection to CANbus-based engines is available. See list below.
  
• Boat must have NMEA 2000 GPS network or NMEA 2000 antenna receiver.
  
• NMEA 0183 will work, but will have slower signal response. Lenco offers a NMEA 2000 GPS antenna receiver and optional stainless steel mounting bracket.

• Yamaha (Command Link Plus requires NMEA 2000 / Yamaha Gateway P/N:6Y98A2D00000)
  
• Evinrude
  
• Honda
  
• Suzuki
  
• Volvo Penta (Non-EVC Engines) (With a Volvo NMEA2000 Gateway - Volvo P/N 3889757)

• Volvo Penta (EVC Engines)
  
• Yanmar
  
• Caterpillar
  
• Cummins
  
• Detroit Diesel
  
• John Deere
  
• Steyr

• Mercury - Verado
  
• Mercury - Optimax with SmartCraft ECU
  
• Mercruiser with SmartCraft ECU
  
• Cummins/Mercruiser w/ SmartCraft ECU

Specifications:

• Box Dimensions: 7"H x 7"W x 15"L WT: 3.8 lbs
• UPC: 874847007283

View full product details

Lenco LED Indicator Integrated Tactile Switch Kit w/Pigtail f/Dual Actuator Systems

$497.99 $595.00

LED Indicator Integrated Tactile Switch Kit w/Pigtail f/Dual Actuator Systems

This switch has the control box integrated into the back of the switch Key Pad. There is no external control box for this kit. Wiring harness is 30"(76.2 cm)in length from the end of the switch bezel.

This technology improves accuracy and integrates the control box functionality into the key pad bezel.

View full product details

Lenco LED Indicator Two-Piece Tactile Switch Kit w/Pigtail f/Dual Actuator Systems

$510.99 $655.00

LED Indicator Two-Piece Tactile Switch Kit w/Pigtail f/Dual Actuator Systems

This LED tactile switch kit has a shortened bezel for consoles which require less depth to mount. Functionality is built into the externally mounted control box and must be mounted separately.

For dealers and consumers who can not use the longer integrated switch due to space limitations behind the console.

Wire Harness Length: 30" (76.2cm)

View full product details

Lenco Standard Lower Mounting Bracket - 3 Bolt

$10.99 $12.85

Standard Lower Mounting Bracket (3 bolt) - VANDAR

View full product details

Lenco Stainless Slide Bracket f/ Hatch Lifts

$49.99 $59.75

In case of power failure, this bracket allows you to pull the hatch open 4" in order to remove pull pin for access.
Includes Attaching Hardware

View full product details

Lenco 9" x 9" Edgemount Trim Tab Kit without Switch Kit 12V

$486.99 $658.00

Edge Mount

Mounts the actuator at the trailing edge of the plane, requiring 4" less transom height than standard mount

Trim tabs make the single most important difference in the way your boat rides and performs. They are optional on some boats but should be as standard as power trim and tilt. Lenco trim tabs make your boat ride smoother, drier, faster and with increased safety whether on a small skiff or a mega-yacht. Lenco's ballscrew design is more reliable, three times more powerful and features an instant response, which makes them very user friendly compared to typical hydraulics. We also like being oil-free and environmentally conscious.

• Instant response electric actuators for precise control
  
• Everything is fully submersible, maintenance-free and sealed for life
  
• Self-locking ballscrew will not drift, even while backing down
  
• 12-gauge laser cut stainless steel trim tab planes
  
• High-impact corrosion-proof mounts look great through years of abuse
  
• Clean, time and space-saving installation
  
• Actuators have high-impact, 50% glass fiber-filled, ultraviolet-resistant nylon case
  
• 316 super buff stainless steel rams

Specifications:

• Box Dimensions: 6"H x 14"W x 14"L WT: 15 lbs
• UPC: 874847000062

View full product details

Lenco 9" x 9" Standard Trim Tab Kit without Switch Kit 12V

$458.99 $621.00

Trim tabs make the single most important difference in the way your boat rides and performs. They are optional on some boats but should be as standard as power trim and tilt. Lenco trim tabs make your boat ride smoother, drier, faster and with increased safety whether on a small skiff or a mega-yacht. Lenco's ballscrew design is more reliable, three times more powerful and features an instant response, which makes them very user friendly compared to typical hydraulics. We also like being oil-free and environmentally conscious.

• Instant response electric actuators for precise control
  
• Everything is fully submersible, maintenance-free and sealed for life
  
• Self-locking ballscrew will not drift, even while backing down
  
• 12-gauge laser cut stainless steel trim tab planes
  
• High-impact corrosion-proof mounts look great through years of abuse
  
• Clean, time and space-saving installation
  
• Actuators have high-impact, 50% glass fiber-filled, ultraviolet-resistant nylon case
  
• 316 super buff stainless steel rams

Specifications:

• Box Dimensions: 6"H x 14"W x 14"L WT: 15 lbs
• UPC: 874847004213

View full product details

Lenco 9" x 18" Standard Trim Tab Kit without Switch Kit 12V

$506.99 $686.00

Trim tabs make the single most important difference in the way your boat rides and performs. They are optional on some boats but should be as standard as power trim and tilt. Lenco trim tabs make your boat ride smoother, drier, faster and with increased safety whether on a small skiff or a mega-yacht. Lenco's ballscrew design is more reliable, three times more powerful and features an instant response, which makes them very user friendly compared to typical hydraulics. We also like being oil-free and environmentally conscious.

• Instant response electric actuators for precise control
  
• Everything is fully submersible, maintenance-free and sealed for life
  
• Self-locking ballscrew will not drift, even while backing down
  
• 12-gauge laser cut stainless steel trim tab planes
  
• High-impact corrosion-proof mounts look great through years of abuse
  
• Clean, time and space-saving installation
  
• Actuators have high-impact, 50% glass fiber-filled, ultraviolet-resistant nylon case
  
• 316 super buff stainless steel rams

Specifications:

• Box Dimensions: 7"H x 13"W x 25"L WT: 22 lbs
• UPC: 874847004237

View full product details

Lenco 12" x 18" Edgemount Trim Tab Kit w/o Switch Kit 12V

$596.99 $808.00

Edge Mount

Mounts the actuator at the trailing edge of the plane, requiring 4" less transom height than standard mount

Trim tabs make the single most important difference in the way your boat rides and performs. They are optional on some boats but should be as standard as power trim and tilt. Lenco trim tabs make your boat ride smoother, drier, faster and with increased safety whether on a small skiff or a mega-yacht. Lenco's ballscrew design is more reliable, three times more powerful and features an instant response, which makes them very user friendly compared to typical hydraulics. We also like being oil-free and environmentally conscious.

• Instant response electric actuators for precise control
  
• Everything is fully submersible, maintenance-free and sealed for life
  
• Self-locking ballscrew will not drift, even while backing down
  
• 12-gauge laser cut stainless steel trim tab planes
  
• High-impact corrosion-proof mounts look great through years of abuse
  
• Clean, time and space-saving installation
  
• Actuators have high-impact, 50% glass fiber-filled, ultraviolet-resistant nylon case
  
• 316 super buff stainless steel rams

Specifications:

• Box Dimensions: 7"H x 13"W x 25"L WT: 24.8 lbs
• UPC: 874847004398

View full product details

Lenco 12" x 18" Standard Trim Tab Kit without Switch Kit 12V

$541.99 $733.00

Trim tabs make the single most important difference in the way your boat rides and performs. They are optional on some boats but should be as standard as power trim and tilt. Lenco trim tabs make your boat ride smoother, drier, faster and with increased safety whether on a small skiff or a mega-yacht. Lenco's ballscrew design is more reliable, three times more powerful and features an instant response, which makes them very user friendly compared to typical hydraulics. We also like being oil-free and environmentally conscious.

• Instant response electric actuators for precise control
  
• Everything is fully submersible, maintenance-free and sealed for life
  
• Self-locking ballscrew will not drift, even while backing down
  
• 12-gauge laser cut stainless steel trim tab planes
  
• High-impact corrosion-proof mounts look great through years of abuse
  
• Clean, time and space-saving installation
  
• Actuators have high-impact, 50% glass fiber-filled, ultraviolet-resistant nylon case
  
• 316 super buff stainless steel rams

Specifications:

• Box Dimensions: 7"H x 13"W x 25"L WT: 14.5 lbs
• UPC: 874847004299

View full product details

Lenco 9" x 12" Edge Mount Trim Tab Kit w/o Switch

$515.99 $688.00

Edge Mount Trim Tab Kit w/o Switch

Lenco Electric Edge Mount Trim Tab Kits make your boat ride smoother, dryer, faster and with increased safety whether on a small skiff or a large yacht. The Lenco ball screw design is more reliable, three times more powerful and features an instant response, which makes them very user friendly compared to typical hydraulics. Lenco fast response electric actuators are fully submersible with all plug & play waterproof Deutsch connections. Edge Mount actuators mount at the trailing edge of the plane, requiring 4" (10.16 cm) less transom height than Lenco standard mount trim tabs.

Suggested Boat Length:16'-25'
L" x W": 9" x 12"
Hinge Height: 2"
Minimum Transom Height: 13.5"

Kit Contents

• 2 each of 12-gauge stainless steel trim tab blades
  
• 2 each of #15054-001 actuator with 6' leads & Deutsch plugs
  
• 2 each of #30133-103 20' actuator extension wiring harnesses
  
• 2 each of #15085-001 (116) upper mounting brackets with gland seal
  
• 2 each of #50014-001 (119) lower mounting brackets
  
• 1 each of the Lenco owner's / installation manual
  
• All necessary stainless steel mounting hardware

• Blades: 12 Gauge Stainless Steel
  
• Finish:Smooth
  
• Class: Fuel Efficient
  
• Compliance: CE Certified
  
• Compatibility: Any Boat

Specifications:

• Construction: Stainless Steel
• Boat Length - Max (Feet): 16'-25'
• Box Dimensions: 5"H x 13"W x 14"L WT: 17.3 lbs
• UPC: 874847004367

View full product details

Lenco Actuator Extension Harness - 14' - 16 Awg

$27.99 $33.00

Actuator Extension Harness - 14' - 16 Awg

• 14' Deutsch-Connected Extension
  
• 16 Awg
  
• Abyc Compliant

View full product details

Lenco Actuator Extension Harness - 20' - 14 Awg

$33.99 $40.00

Actuator Extension Harness - 20' - 14 Awg

• 20' Deutsch-Connected Extension
  
• 14 Awg
  
• Abyc Compliant

View full product details

Lenco NMEA 2000 Tee Connector

$24.99 $26.00

NMEA 2000 Tee Connector

Lenco's NMEA 2000 Tee Connector only.

View full product details

Lenco Flybridge Kit f/ LED Indicator Key Pad f/All-In-One Integrated Tactile Switch - 20'

$174.99 $208.50

Flybridge Kit f/ LED Indicator Key Pad f/All-In-One Integrated Tactile Switch - 20'

Add a second station key pad to your new Integrated Tactile Switch by plugging into the existing harness.

Includes LED Indicator Key Pad & Desired Shielded Length Wire Harness

View full product details

Lenco Universal Actuator Mounting Bracket Replacement Kit 

$26.99 $32.40

Universal Actuator Mounting Bracket Replacement Kit

For use on 1 actuator

Universal Actuator Mounting Bracket replacement kit (for 1 actuator)

Includes:

• 15085-001: Upper Mounting Bracket With Gland Seal - Vandar - (3 Screw, 1 Wire)
• 50015-001D: Standard Upper Mounting Bracket - Vandar - (3 Screw, 1 Wire) (Thru 2007)
• 50014-001D: Standard Lower Mounting Bracket (3 Bolt) - Vandar
• Hardware

View full product details

Lenco 12" x 9" Standard Performance Trim Tab Kit w/LED Indicator Switch Kit 12V

$888.99 $1,203.00

Standard Performance Series Tabs

Standard actuator with 5/16" stainless steel through bolts. 1" turned up edges with 2" taper on the inside. All 12-gauge 304 stainless steel construction with Electro-Polished Blades

We make the best boats better!™

Running wide open in rough seas isn't for the faint of heart. Aggressive boating requires durable boat accessories. Lenco's Standard Performance series of trim tabs are built to handle whatever you or Mother Nature might throw at them. Everything about your boat is designed to go hard and fast. Why should your trim tab system be any different?

• All stainless steel construction (no dissimilar metals), Electro Polished Blades for long lasting good looks
  
• Actuator speed is precise and controllable so there are no surprises at top speeds

• Instant response
  
• Fully submersible, maintenance-free and sealed for life
  
• High-impact, 50% glass fiber-filled, ultraviolet-resistant nylon case

• Self-contained, sealed keypad
  
• Self-contained, sealed control box module
  
• Fade/smudge-proof, laser engraved graphics
  
• Plug & play switch wiring harness connector
  
• Includes 36" power pigtail for control box
  
• 2" hole cut-out size, overall size 2.75" x 2.75"
  
• Built-in retract feature returns tabs to a fully retracted position when power is removed
  
• 2 high-intensity L.E.D. indicator displays show the exact position of our trim tabs at all times
  
• Photo eye reads ambient light and adjusts the L.E.D. indicator display intensity for optimum viewing in direct sunlight
  
• 12 & 24-volt compatibility
  
• Includes Self-Check Feature

• Tactile LED Indicator Switch Kit
  
• 2 actuators with 6' Lead & Deutsch Plugs
  
• 2 12 Gauge SS Electro Polished trim tab planes
  
• 2 20' Actuator Extension Wiring Harness
  
• 2 Upper Mounting Bracket with Gland Seal
  
• 2 Lower Mounting Bracket
  
• All Necessary stainless steel mounting Hardware

Specifications:

• Box Dimensions: 5"H x 14"W x 15"L WT: 21.88 lbs

View full product details

Lenco 18" x 14" Standard Performance Trim Tab Kit w/LED Indicator Switch Kit 12V

$1,100.99 $1,490.00

Standard Performance Series Tabs


Standard actuator with 5/16" stainless steel through bolts. 1" turned up edges with 2" taper on the inside. All 12-gauge 304 stainless steel construction with Electro-Polished Blades

We make the best boats better!™

Running wide open in rough seas isn't for the faint of heart. Aggressive boating requires durable boat accessories. Lenco's Standard Performance series of trim tabs are built to handle whatever you or Mother Nature might throw at them. Everything about your boat is designed to go hard and fast. Why should your trim tab system be any different?

• All stainless steel construction (no dissimilar metals), Electro Polished Blades for long lasting good looks
  
• Actuator speed is precise and controllable so there are no surprises at top speeds

• Instant response
  
• Fully submersible, maintenance-free and sealed for life
  
• High-impact, 50% glass fiber-filled, ultraviolet-resistant nylon case

• Self-contained, sealed keypad
  
• Self-contained, sealed control box module
  
• Fade/smudge-proof, laser engraved graphics
  
• Plug & play switch wiring harness connector
  
• Includes 36" power pigtail for control box
  
• 2" hole cut-out size, overall size 2.75" x 2.75"
  
• Built-in retract feature returns tabs to a fully retracted position when power is removed
  
• 2 high-intensity L.E.D. indicator displays show the exact position of our trim tabs at all times
  
• Photo eye reads ambient light and adjusts the L.E.D. indicator display intensity for optimum viewing in direct sunlight
  
• 12 & 24-volt compatibility
  
• Includes Self-Check Feature

• Tactile LED Indicator Switch Kit
  
• 2 actuators with 6' Lead & Deutsch Plugs
  
• 2 12 Gauge SS Electro Polished trim tab planes
  
• 2 20' Actuator Extension Wiring Harness
  
• 2 Upper Mounting Bracket with Gland Seal
  
• 2 Lower Mounting Bracket
  
• All Necessary stainless steel mounting Hardware

Specifications:

• Box Dimensions: 9"H x 19"W x 24"L WT: 33.7 lbs

View full product details