NMEA 0183 10 Meter Connection Cable
A 10 Meter NMEA 0183 connection cable specifically for Maretron's SSC200 & SSC300 Solid State Compasses.
Engine Management Unit Analog - NMEA2000
Share engine information on the NMEA 2000® bus...
The Actisense EMU-1 is a specialised analogue to NMEA 2000 Gateway which converts data from analogue engine senders into NMEA 2000. The EMU-1 enables NMEA 2000 display devices to monitor the engine on a vessel.
The EMU-1 has a PC based configuration tool that allows the settings inside the EMU-1 to be changed to best suit the engine it is working with, making it a flexible solution for many engine makes and models. Capable of measuring a wide range of engine parameters, the EMU-1 reports how the engine is operating and shares the information across the network.
Designed to simplify the conversion of analogue engine parameters (e.g. Temperature, pressure and RPM) into NMEA 2000 engine PGNs, the EMU-1 simplifies processes and reduces the number of input/output wires required at each engine. Additionally, the EMU-1 also supports the conversion of analogue transmission parameters and battery status to the associated NMEA 2000 PGN's.
The two-part screw terminal connection system allows for an easy pluggable connection to an engine wiring harness.
Multiple engines are supported by the setting of the engine instance using the EMU-1 configuration tool. Currently one EMU-1 per engine is supported. Support for multiple engines on a single EMU-1 is currently planned as a future firmware update.
The customised case ensures that the electronics are sealed while allowing quick access to the electrical connections.
It is recommended that an Actisense NGT-1 NMEA 2000 PC Interface is available for every EMU-1 installation. The NGT-1 can be used to update the Firmware, connect the Configuration Tool and display data on a PC for diagnostic and information purposes, using NMEA Reader. Please visit the NGT-1 page for product details.
NMEA0183 Buffer w/6 ISO-Drive Outputs
Safely drive up to six NMEA Listeners, with power distribution for the connected Talker...
The Actisense NBF-3 NMEA Buffer isolates and buffers NMEA 0183 data, with the power to drive multiple devices.
The NBF-3 can distribute up to six identical, amplified streams of data from one source. The NMEA signals are buffered to ensure that each Listener receives the data at the required voltage levels, providing consistent data quality.
The isolation on the input and each of the outputs ensures the protection of the source Talker device and all the Listening devices. The safe connections mean that a non-isolated device could be connected and the NBF-3 would prevent it from causing any damage to the other equipment in the system. Ground loops often occur when devices are not isolated and can cause irreparable damage. Actisense ISO-Drive technology on the outputs along with the galvanic opto-isolation on the input means you can connect the NBF-3 with complete peace of mind.
The NBF-3 has the addition of power distribution for the NMEA Talker. By having power and data from the same source, cabling requirements are reduced and installation is simple.
NMEA0183 Data Combiner w/RS232
Flexible multiplexing w/preconfigured version for Autoswitching or AIS operation...
The Actisense NDC-4 and NDC-4-USB allow up to five OPTO isolated NMEA 0183 sources to be multiplexed into a single stream*.
Two flexible ISO-Drive outputs allow two different downstream talker baud rates to be created, ensuring maximum system flexibility.
The NDC-4 is flexible and powerful enough to be the heart of a simple system, or one of many Actisense products in a more complex system. It provides complete access to all NMEA 0183 data sources, configurable filters to remove unwanted data, as well as enabling an on-board PC to read and add the combined data stream.
Factory preconfigured versions enable the NDC-4 to be used out of the box for AIS operation (NDC-4-AIS) or as an Autoswitch (NDC-4-ASW).
*Four inputs on the USB version, as the USB interface acts as the fifth channel, overriding the fifth OPTO input.
NMEA0183 to NMEA2000 AIS Configured
Hook up to NMEA 2000 whilst keeping currently installed NMEA 0183 devices...
NGW-1-ISO-AIS is the NMEA 0183 AIS option. This is a pre-configured version of the standard NGW-1-ISO that enables the conversion of NMEA 0183 AIS data to its equivalent in NMEA 2000. This provides an 'out of the box' solution for quick installation with no configuration required. Please see the conversion list in the downloads section to see which AIS conversions the unit can perform.
The Actisense NGW-1 NMEA 2000 Gateway is the easiest way to link between a boats old and new data networks. The NGW-1 can convert NMEA 0183 data into NMEA 2000 data and vice-versa.
Using the advanced configuration software provided, it is straightforward to set up which data conversions are required for both directions.
Please go to the Downloads tab to see the up to date list of conversions the various configurations can handle.
Multiple NGW-1 units can be used to multiplex numerous NMEA 0183 devices onto the NMEA 2000 network, using the network as a means of combining and transferring all data items from one place to another.
The Actisense NMEA Reader software utility allows the NGW-1 user to view and understand (in detail) the translated NMEA 0183 sentences output by an NGW-1 directly.
Benefits of the NGW-1: